JuniperSRX550防火墙NAT配置-创新互联

一、Source NAT

对于不需要做NAT的网段(比如IPSec×××),需要先关闭这些地址的NAT(如果没有则跳过)

成都创新互联公司主要从事成都网站设计、成都网站建设、网页设计、企业做网站、公司建网站等业务。立足成都服务涟源,十载网站建设经验,价格优惠、服务专业,欢迎来电咨询建站服务:028-86922220

set security nat source rule-set trust-untrust rule no-nat match source-address 192.168.0.0/16

set security nat source rule-set trust-untrust rule no-nat match destination-address 10.10.0.0/24

set security nat source rule-set trust-untrust rule no-nat then source-nat off

对于需要上网或者所有的网段(做地址转换的网段),做source-nat

首先定义一个地址池(要转换的公网地址):

set security nat source pool natpool1 address 112.48.20.11/32 to 112.48.20.15/32

set security nat source pool natpool2 address 112.48.20.21/32 to 112.48.20.30/32

配置NAT规则匹配源、目、转换地址池

set security nat source rule-set trust-untrust from zone trust

set security nat source rule-set trust-untrust to zone untrust

//匹配特定的地址进行转换(没有特定可省略)

set security nat source rule-set trust-untrust rule nat1 match source-address 0.0.0.0/0

set security nat source rule-set trust-untrust rule nat1 match destination-address 183.253.58.253/32

set security nat source rule-set trust-untrust rule nat1 then source-nat pool natpool1

//默认所有的源、目地址进行转换

set security nat source rule-set trust-untrust rule nat2 match source-address 0.0.0.0/0

set security nat source rule-set trust-untrust rule nat2 match destination-address 0.0.0.0/0

set security nat source rule-set trust-untrust rule nat2 then source-nat pool natpool2

如果NAT地址池有多个地址,除了接口地址,那么其它地址需要做proxy-arp

set security nat proxy-arp interface ge-0/0/0.0 address 112.48.20.11/32 to 112.48.20.15/32

set security nat proxy-arp interface ge-0/0/0.0 address 112.48.20.21/32 to 112.48.20.30/32

做完这些就可以了? NO! NO! NO!防火墙域间策略不能忘

//首先定义两个地址池,并加入到地址组NET中

set security zones security-zone trust address-book address192.168.100.0 192.168.100.0/24

set security zones security-zone trust address-book address192.168.200.0 192.168.200.0/24

set security zones security-zone trust address-book address-setNET address192.168.100.0

set security zones security-zone trust address-book address-setNET address192.168.200.0

//将地址组匹配到trust到untrust的策略中,并放行

set security policies from-zone trust to-zone untrust policy1 match source-addressNET

set security policies from-zone trust to-zone untrust policy1 match destination-address any

set security policies from-zone trust to-zone untrust policy1 match application any

set security policies from-zone trust to-zone untrust policy1 then permit

到此,这192.168.100.0和192.168.200.0就可以通过NAT上网了

二、Destination NAT

部分服务器需要映射到公网去,怎么做呢?那么往下看:

//首先创建要映射的服务器地址池(包括IP地址和端口)

set security nat destination pool1 address 192.168.168.168/32

set security nat destination pool1 address port 443

//创建Destination NAT规则要映射的服务器地址池(包括IP地址和端口)

set security nat destination rule-set desnat from zoneuntrust

set security nat destination rule-set desnatto zone trust

set security nat destination rule-set desnat ruleserver1 match source-address 0.0.0.0/0

//匹配访问112.48.20.2的4430端口转换到内网服务器的443端口

set security nat destination rule-set desnat ruleserver1 match destination-address 112.48.20.2/32

set security nat destination rule-set desnat ruleserver1 match destination-port4430

set security nat destination rule-set desnat ruleserver1 then destination-nat pool 1

还有必不可少的防火墙域间策略

//创建内网服务器地址组及端口

set security zones security-zone trust address-book addressserver1 192.168.168.168/32

set applications application Service_4430 term Service_4430 protocol tcp

set applications application Service_4430 term Service_4430 source-port 0-65535

set applications application Service_4430 term Service_4430 destination-port4430-4430

//创建untrust到trust的策略,目前地址匹配内网服务器地址及端口

set security policies from-zone untrust to-zone trust policy1 match source-address any

set security policies from-zone untrust to-zone trust policy1 match destination-addressserver1

set security policies from-zone untrust to-zone trust policy1 match application Service_4430

set security policies from-zone untrust to-zone trust policy1 then permit

至此,外网就可以使用http://112.48.20.2:4430/访问内网的服务器了

还有一个问题,此时内网的用户却不能使用这个公网地址访问内部的服务器,这个需要在NAT上再做一个内部的地址转换,如下:

//创建一个源地址映射的地址池(内部服务器映射的地址)

set security nat source pool sorpool4 address 112.48.20.2/32

//创建trust到trust的策略如下

set security nat source rule-set trust-trust from zone trust

set security nat source rule-set trust-trust to zone trust

set security nat source rule-set trust-trust ruleserver1 match source-address 0.0.0.0/0

set security nat source rule-set trust-trust ruleserver1 match destination-address192.168.168.168/32

set security nat source rule-set trust-trust rule server1 match destination-port443

set security nat source rule-set trust-trust rule server1 then source-nat pool sorpool4

至此,内网也可以通过公网地址访问内部服务器了!!!

如有雷同,纯属巧合,欢迎指正!

另外有需要云服务器可以了解下创新互联cdcxhl.cn,海内外云服务器15元起步,三天无理由+7*72小时售后在线,公司持有idc许可证,提供“云服务器、裸金属服务器、高防服务器、香港服务器、美国服务器、虚拟主机、免备案服务器”等云主机租用服务以及企业上云的综合解决方案,具有“安全稳定、简单易用、服务可用性高、性价比高”等特点与优势,专为企业上云打造定制,能够满足用户丰富、多元化的应用场景需求。


网站栏目:JuniperSRX550防火墙NAT配置-创新互联
转载来于:http://myzitong.com/article/pocoi.html